- Sold in pairs - Allen wrench included
When you can’t even see a part, you might forget about it, but it doesn’t mean its not important. Flat tires are probably the most common bicycle failures. Many times, flats are caused by the rims, specifically the lack of protection from the rims' sharp edges. Good rim strips didn’t exist for BMX rims. They work well and improve the function of any 20 inch rim. If you forget about them, that means they are doing their job.
Odyssey's custom-designed Par Ends come standard with all of their grips. Its special plastic composite will not shatter like cheap bar ends do, and they’re very lightweight. The Par End is a combination of the over-the-bar-style cap and the inside-the-bar-style to prevent the inner portion from blowing out like it does on ordinary press-fit bar ends. Comes stock on all of Odyssey's grips.
$7.99 - $8.50
- Upper cables for Odyssey's Gyro G3 (sold separately) - Universal fit. - Upper cables only.
- Lower cables for Odyssey's Gyro G3 (sold separately). - Universal fit. - Lower cables only.
$8.50 - $8.99
The Slim by Four is a BMX-specific brake pad with a symmetrical shape designed for both forwards and backwards braking. A custom inner frame helps to stiffen the pad and prevents excessive braking power from being lost to flex. SPECS - Clear and Gum colored “Soft” compound pads provide extra grip on powder coated rims. - Black “Normal” compound Slim-By-Four pads are the most popular pad choice for most riders.
One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable too. The Ghost Pad addresses the hassles of brake pad installation by eliminating the traditional dome shaped washers used for toe-in. The pad improves stiffness by building the toe-in into the pad shape and utilizing a solid extruded aluminum frame at its core. The Ghost Pad’s assembly consists of simply lining it up with the rim and tightening down an M6 female bolt. Comes stock on the Springfield brake. SPECS Hardware: - In-bound bolt, 5mm Hex Key, M6x1.0 Thread - Pad Material: Black (standard) or Clear Rubber (Soft) - Weight: 1.0oz / 28g (pair)
$9.99 - $13.99
Broc Raiford can bunnyhop over a house so it’s only right that he has his own grips to hold on to. Broc’s signature grip comes in at 160mm in length and features rope detailing on the ends to tie in with Broc’s nautical theme.
The Odyssey K-Shield Linear cable features a pre-stretched inner Slic Kable covered in a linear casing to prevent binding and an outer K-Shield mesh housing for less weight over a standard steel mesh housing (2.9 oz). - Black - 60 – 65mm
One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable. The Springfield lever is easy to install and remove without having to wrestle grips on and off. An ordinary hinged clamp can be bulky and expensive so a new clamping design made specifically for die-casting was used. This approach keeps the lever reliable and affordable. The lever handle is the same comfortable shape as the proven Monolever Medium blade.
In addition to updating Aaron’s tire, Odyssey also wanted to update his signature grip. The updated “Boss” grip features a low profile block pattern which will match his tire, and comes in at 158mm. These will feel similar to his original grip, but improved and with all new styling.
$13.99 - $25.00
One of the most successful and popular pedals, and for good reason with its extremely simple, lightweight, inexpensive and famously durable plastic-bodied design. Often duplicated but never replicated. - High-strength plastic composite
Odyssey took their proven Linear Slic Kable housing and replaced the steel linear wire with aluminum. Utilizing the aluminum wire in the housing saves you significant weight, roughly 30%. This cable also features their specially designed “volcano” ferrules that they’ve used since 2008 to prevent housing blowouts. This Kable also comes with color-coaded inner wires and ball ends to differentiate between their regular Linear’s Race Linear Slic Kable. - Length: 60 – 65mm - Black
$17.99 - $19.99
For the Bluebird chain, Odyssey took the proven and reliable KMC 510-HX chain and added a permanently attached, factory installed half-link to one end. When the chain is trimmed to size you can easily decide whether or not to use the half-link. Original factory assembled pin joints are radically stronger than workshop assembled ones, so this is a huge benefit.
One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable. The Springfield brake drops the two ordinary (and confusing) brake springs and replaces them with one central spring that applies the same force to each arm, requiring no additional adjustment. This makes assembly incredibly easy–just bolt it on and go. The brake arms are designed to maximize stiffness and save weight without adding excessive cost. By die-casting the arms and using shared tooling to make each side, the Springfield meets all of the original design goals, resulting in a very powerful and affordable brake.
The 4.5-inch peg features a full 4130 core with a long-lasting, fast-sliding, plastic sleeve. - Sold individually - 14mm with 3/8” adapters only - Replacement sleeves sold separately - 4.5" (length) x 1.5" (outer diameter) - 4.5 oz (9 oz for a pair)
Odyssey's original dual cable detangler system has been the industry standard since day one. Odyssey has been making the Gyro since 1986 and constantly improving it along the way. Everything you need to run a Gyro. Odyssey Gyro cables and upper and lower cable stops included.
This custom 7075-T6 aluminum pre-load bolt design is included with every Odyssey fork. - Fits both a 6mm and 8mm allen key. - Front brake cable thru-way hole for removal without disconnecting brake hardware. - Designed with an easy-cut thread groove if you cut your fork’s steerer tube down.
The Monolever was an instant classic and has become a clear favorite with pro riders around the world because of its familiar feel, smooth edges and variety of handle options.
$23.99 - $24.99
- 4140 Chromoly - 3 Possible peg positions for longer peg life - 14mm with 3/8-inch adapters included - 4 inches (length) x 1-3/8 inches (outer diameter) - Sold in pairs - 8.75 oz (17.5 oz for a pair)
New dust cap design, with Monogram laser etched logo, for a cleaner look to accommodate a taller riding set up with less spacers. Same quality as Odyssey's Pro Headset using high-quality sealed bearings and a precision tapered wedge to keep the headset tight at all times. FEATURES - High-quality sealed bearings. - Color matched spacers included. - 15mm dust cap. With 3mm, and 2mm spacers - Laser etched Odyssey bearings. SPECS - Campagnolo standard spec. - 1 1/8-inch integrated headset. - 45º tapered bearings - 41.8mm outer diameter (fits 42mm BMX head tubes).
This plastic peg features a full 4130 core with a long-lasting, fast-sliding, plastic sleeve. - 1.5-inch outer diameter - 14mm with 3/8-inch adapter - Sold individually - Weight: 7.6oz - Replacement sleeves sold separately
$25.99 - $34.99
Tom likes to ride fast and go very high. These tires were designed to help him do just that. With a fast center tread, these tires are made for park, street and even dirt too. The side profile is reminiscent of a motorcycle tire as well, which is a nod to Tom’s motorcycle lovin’ ways.
Odyssey is proud to offer their new tripod post. It allows for the two most popular seat angles amongst riders and it’s clean, light and easy to install. SPECS - 25.4mm diameter - 6061-T6 Aluminium, CNC machined
- Straight gauge spokes with a proprietary grade of stainless steel that is as good or better than the materials used by the world’s most renowned spoke makers. - Sized and dimensioned specifically for BMX.
- Made to fit crank spindles and press-fit Mid BB frames. - Simple and easy to install. - Includes an assortment of spacers to optimize chainline and crank clearance. - Odyssey 6061-T6 aluminum dust spacer included.
It’s a traditional straight up pivotal design with a 200mm length.
Aaron Ross's signature BOSS seat features an updated pattern to match his signature tires. Back by popular demand here’s the Fat Capital version. It features larger padding that wraps around Odyssey's custom designed, wider-shaped pivotal base. Specially reinforced for strength at all the right spots. This Tripod version provides a wider base, and slightly beefier padding and shape than its Pivotal counterpart. It offers a cleaner look, while still being reinforced for strength.
Mike Aitken's original signature seat size and shape.
Chase Gouin’s signature tire. Predictable during tight turns and made to roll smooth at high speeds. Horizontal tread grooves provide shoe traction only when you need them to. This modern interpretation of one of the most popular tires ever made is used regularly by street riders too. Now available with a Special Compound tread durometer for polished indoor floors. 100 PSI, of course.
Page 1 of 2 Next page